• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work up above the ground, moving massive glass panes. They adhere to strict safety guidelines and often work under harsh weather conditions.

While wearing protective clothing remove all glaze putty and glazing points using a utility knife. A heat gun may help soften the old putty and make it easier to remove.

Replacement

If a window pane breaks, it can be tempting to repair the glass rather than replace it. It is more cost-effective to replace a window and it can also help you to avoid other issues in the efficiency of your home. It is also important to consider the type of glass that is damaged to determine if it is temporary or if you will require a more permanent solution.

The first step in fixing a broken window is to take off the sash, or frame and lay it flat on a table. While wearing eye protection, carefully move the frame and remove any shards remaining within the window repairs. Utilize a utility knife to scrape off the glazing compound, as well as the glazing points that hold the window in place. Keep the track of the components and their locations so that they can be put back in place.

After removing the frame and sash you can start preparing to replace the glass. Before you do so, make sure that the opening in the frame is properly designed for the replacement window. Measure both ways across the opening, and then subtract 1/8 inch from each measurement in order to leave space for expansion and contraction of the frame and glass. Then, buy double-strength glass cut to these exact dimensions. It is a good idea also to purchase enough glazier's clips or points to install every 6 inches around the window pane.

If the manufacturer is responsible you should contact them and make a claim. After the new glass has been installed, it is important to cover it with a thin layer of glaziers compound. Once the compound is dry it is possible to paint the frame to the color of the.

If your crack is longer than an inch in length You can stop it from spreading by cutting an arc that is just a little beyond the crack. This technique isn't 100% foolproof but it can slow the progression of the cracked until you are able to take permanent measures.

Repair

Professional window installers know how to handle various kinds of glass types, and they have the tools needed to complete a proper job. They also know the best ways to dispose of waste, and are less likely to leave waste that are left behind, which could injure family members or pets. They're also familiar with different window types and are capable of identifying issues that aren't apparent to the uninitiated homeowner.

Before you begin the process of fixing cracked window glass, be sure to wear safety glasses and gloves. A minor crack could cause shards of glass to fly away, posing a danger to anyone who lives in or around the home. It's important to determine what caused the crack, since this could prevent future problems.

Begin by creating an epoxy mix that is two-part. These are usually a 50/50 mix of hardener and resin, and they must be quickly mixed. After the mix has been made then apply it directly to the crack and allow it to dry. It will take just a few minutes but it's important to do it quickly because the mixture is very thick and fast-drying.

Once the epoxy has dried, you can take off excess epoxy with a blade. Then, you'll need to clean the area around the crack of glass. If you do not clean the area in a proper manner, the debris could cause further damage to your glass. After cleaning the glass, use a putty knife to smooth the compound along the edge of the window and match it to the frame made of wood.

You could consider using a plastic cover for a more durable option. You can cover the glass using masking tape or a sturdy trash bag. This will prevent the crack from growing and will also block out water, wind, bugs, and debris.

If you're not able to get to the window in a timely manner then you can apply silicone sealant to make an interim repair. Simply apply a small amount of the substance around the outside of the damaged pane. It won't seal the gap between the glass and the frame completely but it will hold the broken piece in place until you can fix it.

Repainting

If your glass windows are old, you might consider repainting them. This is a low-cost alternative to replace your windows and can give your house a new look. Before painting, ensure that the surface is clean. Use soap or rubbing alcohol and water to wash away oil smudges, and other residues that could prevent paint from adhering. You should also wear rubber gloves when working on glass to avoid transferring your own oils onto the glass surface. Finally, you should apply several thin coats of paint instead of a thick layer. This will help the paint last longer and keep your windows looking smooth and even.

If you're planning on repainting your glass windows, ensure that you have the proper tools nearby. You'll need a brush, sponge, painter's adhesive, a ruler, toothpicks, and a few other tools like a rag or paper towel. You'll also need the paint and brushes you'll use for the project on hand. Follow the manufacturer's instructions. Have patience as it can take a while for the paint to completely dry.

It is also important to ensure that the space you're working is well ventilated if you're using solvent-based paint. This will decrease the risk of breathing in toxic chemicals and permit the paint to dry faster. You should also make sure you have a mask to protect yourself for any spray paints that you use.

For older glass windows, it is necessary to prepare the surface before painting. Use soap and warm water to thoroughly clean the glass window. Then, rub alcohol on any oil or grease residues that might hinder the adhesion of the paint. Make sure the windows are completely dry prior to coating them.

If your glass windows are energy-efficient dual pane windows, you may be eligible to submit a claim to the window manufacturer or dealer that sold them to pay any repair or replacement costs. This is especially true if your windows are still under warranty and you've had multiple problems with condensation or damaged glass.

Sealing

There are a variety of options to address the issue regardless of whether you have an old double-pane glass with a cracked seal, or if you own an upgraded insulated unit (IGU) that has experienced fogging. The most expensive option is to replace the frame and insulated unit but it may be necessary if condensation or fog cause energy loss. Other options include replacing the existing IGU with a single-pane, or repairing it by drilling a small hole through the bottom of the unit, and then filling the solution with anti-fog.

You can also fill in the gap between the window frame and the threshold or sill with a felt strip, vinyl v-strips, or door sweep. Felt is inexpensive and can be fixed by gluing, nailing or stapled to the frame but it doesn't provide much protection from moisture. Vinyl v-strip weather stripping is durable and easy to install however, it can be costly and is usually reserved for areas that are exposed to high abrasion. Door sweeps are easy to nail in place and are inexpensive. However, they offer very little or no protection between the threshold and air.

To repair a damaged window seal, use a putty blade to scrape off the caulk. Wearing gloves and eye protection take care to remove the glazing points, which are tiny fasteners that hold the glass into the frame's recess with sharp, pointed edges. After getting rid of the glazing points clean out the grooves, then sand the wood. Clean any sanding dust, then seal the bare wooden surface with a linseed-oil-based paint or clear sealer.

Traditional glazing putty is applied using the help of a putty blade or caulking gun, but the knife is a better, more precise application and creates a better seal. Select a putty made specifically for glass, as it will be more durable and adhere better.

Apply a small amount of the putty to the inner edge of the frame where it touches the glass. Slide the window into frame so that the scribed line on glass lines up with edge of frame. Apply pressure to the glass to force the putty and glass into a tight seal. Smooth the compound using an ungloved finger and then wipe off any caulk that is applied incorrectly or spills that are not properly wiped away prior to drying.